Practical Soldering and Wiring Skills for FTC Students

FIRST Tech Challenge (FTC) students often reach the point where breadboards and plug-in modules are no longer enough. Their robots need permanent sensor connections, protected power leads and harnesses that survive vibration, handling and transport. Teaching solder joints and wire preparation turns those needs into practical engineering work rather than a last-minute build problem.

A useful electronics lesson joins three strands: making a secure mechanical connection, creating a safe circuit and recording the work. Students should learn why a joint fails, not simply copy a sequence. That mindset turns soldering into the iterative engineering practice valued in FIRST competitions.

Start with low-voltage circuits and introduce a temperature-controlled iron gradually. Teach wire stripping, tinning, through-hole joints, crimped connectors and continuity checks in that order, using spare boards before students work on a robot. Mentors can adapt the sequence for different ages and previous experience.

Regional support can determine whether a new team survives its first season. Teams looking for guidance on starting a team, finding mentors or arranging sponsorship can use Maryland program enquiries as a model for the questions a regional FIRST partner should be ready to answer.

Why practical electronics belongs in FTC builds

Soldering creates a permanent joint between a component lead and a board or wire. A sound joint offers mechanical strength, low electrical resistance and some resistance to corrosion. These qualities make it useful for sensor modules, motor-driver boards and small custom circuits, provided the iron is controlled and the joint is properly made.

Wiring involves more than attaching a wire to a terminal. Reliable robot wiring also requires suitable conductor sizes, secure connectors, strain relief, clear polarity and a layout that protects vulnerable signal wires from motor power. Teaching both skills helps students understand why a working prototype may still fail in competition.

The transferable goal is evidence-based troubleshooting. Students who can read a schematic, follow a pin label and test a connection can diagnose a fault systematically. An engineering notebook recording wire colours, connector types and test results also turns temporary fixes into knowledge the whole team can use.

Designing a safe, age-appropriate course

Most FTC participants are secondary-school age, although teams include students with widely different experience. FIRST LEGO League and Jr.FLL members can begin with wire identification, connector crimping and prepared low-voltage boards. Any student using a hot iron needs direct supervision, a clear workspace and a rule that the tool never leaves the bench.

Australian schools must apply the Work Health and Safety laws of their state or territory. Safe Work Australia publishes guidance on hazardous substances, solder fumes and lead exposure; Victorian schools can also consult WorkSafe Victoria. Ventilation and other controls belong in the activity plan, not in an improvised response after a spill or exposure.

Australian students may build in after-school clubs, weekend sessions or shared makerspaces in Melbourne, Sydney and other cities. Plan short sessions around a demonstration, guided practice and a test. A 20-minute bench rotation can be followed by a classroom task reviewing polarity, resistance and component orientation. For extension ideas beyond the robot, educators can browse Rednatic learning resources and select low-voltage projects that reinforce the same habits.

Setting up the electronics workshop

Australia’s 230–240-volt mains supply adds a workshop risk that teams should not treat casually. Bench power supplies and chargers need sound leads, suitable Type I plugs under AS/NZS 3112 and protection suited to the circuit. Schools should follow local rules for residual current devices and portable-equipment testing rather than relying on memory.

The local electronics market supports practical training. Australian suppliers such as Altronics, Jaycar and Melbourne-based Core Electronics sell irons, solder, crimpers and common connectors, while online purchasing gives regional teams broader access. Compare stock, delivery times and warranties before a build weekend; a spare tip and iron may be more useful than unfamiliar components bought in bulk.

Use temperature-controlled stations, lead-free solder, compatible flux, desoldering braid and heat-shrink tubing. Lead-free metal reduces lead exposure, but it still produces flux fumes and generally requires more heat than leaded solder. Any lead-containing solder needs restricted handling and proper hygiene.

Provide individual sponges or brass cleaners, a burn kit and access to cool running water. For a burn, cool the affected area under running water for 20 minutes and follow the school’s first-aid procedure. Keep irons in their stands, position cords safely and arrange tools so students do not need to reach across another person’s workspace.

Teaching joints and choosing connections

A reliable method has six actions: clean and dry the pad, insert the component, apply a small amount of suitable flux, heat the pad and lead together, feed solder into the joint and remove the iron while the solder solidifies. The iron heats the connection; melting solder on the tip usually produces a poor joint.

Wire preparation includes stripping the correct length, twisting stranded conductors and tinning them with a thin solder layer. A sound joint looks shiny and concave rather than a round bead. Students practise on scrap boards, inspect their work under good light and test for continuity before fitting a component to the robot.

Connection method Typical use Main advantage Common failure
Soldered joint Sensor and driver boards Compact, permanent and electrically reliable Cold joint, bridging or a dry solder ball
Crimp connector Power leads and detachable accessories Strong mechanical grip and replaceable termination Loose crimp, damaged strand or poor strain relief
Plug-in connector Modules needing frequent servicing Fast changes without rebuilding the harness Incorrect mating, bent pin or loose latch

Choice should follow service needs. A soldered joint suits a fixed module, while a crimped or locking connector allows replacement during a busy build night. Students can explain their choice in an engineering notebook, including whether the connection carries signal or power and what test would reveal a hidden fault.

Wiring robots that remain reliable

For a robot harness, measure each run and select wire gauge for the load, voltage drop and distance. Keep motor-current paths short and substantial, while sensor and communications wiring can use finer conductors. Use locking connectors where vibration is likely, and provide strain relief so a tug loads the connector rather than the solder joint.

Good documentation removes guesswork. Label both ends of every lead, record connector pinouts and mark battery positive clearly. Heat-shrink tubing should cover exposed conductor, but it must be fitted before the connector is assembled. Keep a printed or digital wiring diagram beside the robot during testing and competition preparation.

Finish each subsystem with a power-off inspection. Check polarity, component orientation, loose strands, accidental bridges and connector seating. Use a multimeter to check intended continuity, look for shorts and verify supply voltage before connecting the battery. Teams sharing a makerspace in Melbourne, Sydney or Brisbane should reserve a power-off test area, and a second person should verify connections during first power-up.

Practising, assessing and troubleshooting

Assessment works best when speed earns no advantage. Use a small practice board containing an LED, resistor and connector, then ask students to produce a joint, secure the wires and document the test. A checklist can cover safe tool handling, component orientation, joint appearance, continuity, strain relief and a clean bench. Students should retest after feedback.

Common faults provide useful practice. A dull, cracked or movable joint suggests a cold connection; a bridge links adjacent pads; a connector that becomes warm under load may contain loose copper strands. Learners can isolate one section at a time, consult the schematic, make one change and record the result.

Rotate technical roles so every member participates in component preparation, wiring, test logging and lead-safety checks. Mentors can ask students to explain a joint or circuit to a teammate, which exposes gaps in understanding without singling anyone out. A repaired robot then demonstrates core FIRST values: persistence, cooperation and gracious professionalism.


Before the next build night, choose one simple trainer circuit, confirm that every bench has ventilation and a checked iron, and assign a mentor to demonstrate the full sequence. Give students practice boards and a clear stopping rule: if a joint does not pass inspection, it is reheated or replaced rather than hurried into service.

Run the first supervised soldering session this term with a simple LED circuit, a documented safety check and a practice board for every pair. Equip the benches, brief the students and make the first joint a safe success.